Unitech PT600 Instrukcja Użytkownika

USER’S GUIDE PORTABLE DATA COLLECTION TERMINAL PT600

- 7 -Diagram shown with a clip-on pen scanner 45° 45°

- 8 -1.2 Interface Ports The PT600 has a RS232C serial port with miniature RJ10 connector, Communication by Infrared LED which on the left side of

- 9 -1.3 Using the Keyboard The keypad of PT600 consists of 27 rubber keys, the  key is used to switch on/off the unit and other 26 keys are use

- 10 -NORMAL mode Keyboard of the PT600 is initialized to normal mode after powered on. In normal mode, the cursor is a block sign and the keyboard

- 11 -ALPHA mode Press [ALPHA] key to toggle between normal mode and alpha mode of keyboard. In alpha mode, the cursor is an underscore sign and th

- 12 -1.5 Application Development Environment The system of PT600 provides DOS functions and device drivers for application development, including

- 13 -1.6 Optional Charging/Communication Cradle An optional charging/communication cradle (docking station), PT016, gives users a convenient acce

- 14 -Chapter 2 Power System 2.1 Power Supply Main Power The PDT is operated by a rechargeable NiMH battery pack with two AA size 1.2V 1500mAH c

- 15 -When the main battery low condition occurs, the main battery can continue to supply power for about 10 ~ 30 minutes, however the unit may rea

- 16 - Remove battery pack Remove backup battery Lithium Back up Battery 1. Refer to the procedure in previous paragraph, un-screw the bac

NOTICE The unit is equipped with a NiMH battery pack, however it may not be powered on due to discharging of the battery by putting in storage for a

- 17 -2.4 Recharging the Battery Pack When the PDT shows “Main battery low” message or sign , the battery pack in PDT needs to be recharged. There

- 18 -Charging Considerations It is important to consider the surrounding temperature whenever you are charging the NiMH battery pack. The process

- 19 -Chapter 3 Operation The system of PDT may operate in various modes for different purposes. The figure below shows the operating flow of th

- 20 - The first line indicates the model code and version number (e.g. V1.00). The second line shows the size of the total installed RAM (i.e. 46

- 21 -from a Host computer. In this mode, data input from bar code reader or keyboard is displayed on screen and output to RS-232 port. Data receiv

- 22 -TYP This command dumps the content of a file on the PDT's LCD. The content of the file will be displayed 128 (16 character x 8 line) cha

- 23 -1. DATE & TIME: set system clock/calendar When selects “1.DATE & TIME” in SET command menu, the screen as right will be shown on PDT’

- 24 -3.4 Upload/Download by ESC Command The way to make file upload/download by Kermit server described in section 3.2 will need the operator to

- 25 -Chapter 4 Built-in Application: FormCaching The system of PDT includes a built-in application, FormCaching, that allows user to create a

- 26 -4.2 How to Create a FormCaching You will need to enter Supervisor mode and select “4.FORM” category in order to set the configuration of For

Table of Content Page Chapter 1 Introduction ... 1 1.1 Technical Specification ...

- 27 -After collecting data, the FORM.DAT file can be uploaded to host either by invoking kermit server in User mode described in section 3.2 or re

- 28 - Warning This is a Class A product in a domestic environment this product may cause radio interference in which case the user may be required

- 1 -Chapter 1 Introduction The PT600 Portable Data Terminal, referred as PDT hereafter, with integrated laser scanner or pen scanner is a rugged,

- 2 -1.1 Technical Specification SOFTWARE PROGRAMMING TOOLS Language Assembly, C language (MSC, Turbo C, Visual C) JobGen Plus A Windows-based tra

- 3 -COMMUNICATION Interface One EIA RS232C with miniature DIN-9p male connector, Support TX/RX, CTS/RTS, GND, up to 57.6Kbps (defaul

- 4 - • Built-in power-on self test and diagnostic program • Host command remote control Integrated Laser Diode Scanner • Scan rate 36 scans/se

- 5 -Depth of Field diagram

- 6 -